LITHONIA 228G9L 5IN IC/NON-IC REMODEL HSNG GSKT L5R GSKT R6
Product Details
Attributes
Features
Resources
Lithonia Lighting®, L5R GSKT R6, Lighting Housing, 5 in Aperture, Series: L5R, 120 VAC, 5-5/8 in Ceiling Opening, Incandescent Lamp, 1 Lamps, Insulated Insulation, Ceiling Mounting, For Use With: 2x8 Remodel Construction, 5 in Diameter, 11-3/4 in Height, 10.13 in Width, Steel Housing Material, Nickel
Lithonia Lighting’s 5" Incandescent Remodel Housing is intended for use with recessed incandescent housings for 2x8 remodel applications. The housing is approved for direct burial in insulation and all ceiling and wiring types. Construction is air-tight, galvanized steel pan with aluminum can and junction box with four built-in ROMEX clamps and ground wire.
- Airtight aluminum housing with heavy gauge galvanized steel raceway arm
- Vertically adjustable mounting brackets that use 16 ga flat bar hangers (included), 1/2 in conduit or C channel T-bar fasteners, provides 3-3/4 in total height adjustment
- All frames are equipped with galvanized steel junction box UL listed for through wire applications
- Junction boxes equipped with (2) combination 1/2 to 3/4 in and (3) 1/2 in knockouts for straight-through conduit runs and removable access doors
- Post installation adjustment possible from below the ceiling
- Maximum 1-1/2 in ceiling thickness
- Rugged, one-piece, die-cast heat sink design for optimum thermal management
- Wet location rated lens is tightly fitted to the housing to reduce the ingress of dust
- Elliptical upper reflector and micro prism lens, provides precise beam control
- Lower splay recesses optical system into the ceiling to reduce glare and provide a traditional PAR look
- Thermal protection provided against improper insulation use
- Remodel clips for installation in existing plaster, sheet rock or mechanical ceilings
- High-efficiency, electronic LED 0 to 10 VDC dimming driver mounted to the junction box, dims luminaire to 15% light output
- For dimming fixture requires two (2) additional low-voltage wires to be pulled
- The system maintains 70% lumen output at more than 50000 hr
- Galvanized steel junction box with three built-in Romex® clamps and ground wire
- Approved for factory assembled wiring only and for direct burial in insulation
- Foam gasketing, aids in airtight installation
- 0.65 spacing criteria
- Rugged, 16 ga galvanized steel mounting frame with torsion spring bracket to mount the finishing module
Product Details
Lithonia Lighting®, L5R GSKT R6, Lighting Housing, 5 in Aperture, Series: L5R, 120 VAC, 5-5/8 in Ceiling Opening, Incandescent Lamp, 1 Lamps, Insulated Insulation, Ceiling Mounting, For Use With: 2x8 Remodel Construction, 5 in Diameter, 11-3/4 in Height, 10.13 in Width, Steel Housing Material, Nickel
Lithonia Lighting’s 5" Incandescent Remodel Housing is intended for use with recessed incandescent housings for 2x8 remodel applications. The housing is approved for direct burial in insulation and all ceiling and wiring types. Construction is air-tight, galvanized steel pan with aluminum can and junction box with four built-in ROMEX clamps and ground wire.
Attributes
Features
- Airtight aluminum housing with heavy gauge galvanized steel raceway arm
- Vertically adjustable mounting brackets that use 16 ga flat bar hangers (included), 1/2 in conduit or C channel T-bar fasteners, provides 3-3/4 in total height adjustment
- All frames are equipped with galvanized steel junction box UL listed for through wire applications
- Junction boxes equipped with (2) combination 1/2 to 3/4 in and (3) 1/2 in knockouts for straight-through conduit runs and removable access doors
- Post installation adjustment possible from below the ceiling
- Maximum 1-1/2 in ceiling thickness
- Rugged, one-piece, die-cast heat sink design for optimum thermal management
- Wet location rated lens is tightly fitted to the housing to reduce the ingress of dust
- Elliptical upper reflector and micro prism lens, provides precise beam control
- Lower splay recesses optical system into the ceiling to reduce glare and provide a traditional PAR look
- Thermal protection provided against improper insulation use
- Remodel clips for installation in existing plaster, sheet rock or mechanical ceilings
- High-efficiency, electronic LED 0 to 10 VDC dimming driver mounted to the junction box, dims luminaire to 15% light output
- For dimming fixture requires two (2) additional low-voltage wires to be pulled
- The system maintains 70% lumen output at more than 50000 hr
- Galvanized steel junction box with three built-in Romex® clamps and ground wire
- Approved for factory assembled wiring only and for direct burial in insulation
- Foam gasketing, aids in airtight installation
- 0.65 spacing criteria
- Rugged, 16 ga galvanized steel mounting frame with torsion spring bracket to mount the finishing module